DIY blend door fix for Jeep WJ WG - AUSJEEPOFFROAD.COM - AJOR


Go Back   AUSJEEPOFFROAD.COM - AJOR > JEEP GARAGE > ZJ WJ WG Grand Cherokee


Portal Register Forums Trading Your Jeep New Garage Mark All Read

Post New Thread  Reply
 
Thread Tools Search this Thread
  #1  
Old 31-08-2016
LEXX's Avatar
LEXX  LEXX is offline
Jeep Dropout
 
Join Date: Jul 2002
Location: Ferntree Gully, Victoria. Australia, Milkyway
Age: 44
Posts: 3,610
What Jeep do I drive?: None
Likes: 8
Liked 74 Times in 41 Posts
Default DIY blend door fix for Jeep WJ WG

ANYONE that wants an alternative:



Like most DIYers I see a problem and the last thing I think about is "where do I take this to get it fixed?" I instead ‎look at a problem and try to outwit traditional solutions. That being said, when I didn't have heat in my Jeep Grand ‎Cherokee (JGC) during our first cold snap I naturally went online to diagnose and solve the problem. What I ‎discovered was this is a very common problem with my model of JGC (1999-2004). I love my Jeep, but the person that ‎designed this blend door actuator system needs to find new work. The design is inherently weak, and relies on a ‎calibration phase that puts intense pressure on the weakest points in the system. Not wanting to repair the faulty ‎design with the same OEM design, I set out to reverse engineer a long-term solution

This website was among the more helpful sites as it provides Jeep's Repair kit instruction. Thanks for a well thought out site, and permission to borrow content.

http://www.denlorstools.com/autoblog...d-door-repair/

This site does a good job of where and how to cut, so I will not re-invent the wheel. I'll show you my solution to the kit from Jeep.

Total Cost of Project:
$1.76 Mending plate ($0.88 x 2)
$3.36 Hinges ($1.18 x 2)

Required Materials / Tools:
4 - 1/8" rivets
1 - Rivet gun
hacksaw or rotary tool (the hacksaw requires more patience than I possess)
Drill



I was able to remove and manipulate the outside most blend door actuator, connector and door without any issue. I ‎could have fabricated all new parts reasonably easily, however the passenger side control would not have worked. ‎So I worked within the OEM connector parts to ensure dual climate control operation.

I decided on a standard 3 inch door hinge as my new pivot point. This stamped steel piece should be more than ‎sufficient to withstand the calibration forces. The door is a reinforcing plate typically used on decks and truss ‎frame construction. These both will be very easy to find at your local home center. The truss plate is found in the ‎pressure treated section.‎ You will need 2 of each to complete both blend door repairs.




The concept of the repair is to rivet the truss plate to the hinge, manipulate the hinge barrel to work on the OEM connector, and cut everything to fit. First I had to remove the pin from the hinge. Use the side of the hinge that has 3 barrels, not the side with 2. This will enable the connectors to reach in their traditional position. Next, select a 5/16" drill bit and drill out the one of the outermost barrels in your first hinge.



Using the OEM connector (the white piece) test the fit. Mark a line where material is to be removed to allow the key to fit. Remove material with a rotory tool or hack saw. The fit between the OEM connector and the hinge has to be incredably tight. The amount of torque that is aplied to this piece in insane. Be patient, b/c you will probably have to install, test, remove and tighten several times before you get it right.




Select 1/8" rivets and drill required holes in the hinge to attach the door, and attach door.




Now that your door is assembled, trim it to fit using the old doors as templates. These new doors will fit very well, and will not work if they are even 1/16" too large. Be sure to pay attention to the side that the notch is removed from - It needs to be on the opposite side of the connector.

Repeat steps 2-5 for the other door.




Cut the head off of one of the hinge pins to serve as the connector between the 2 doors.




This step requires the most patience. To install the far blend door you will probably not be lucky enough to have the connector key in the right place. No worries - disconnect your battery for about 30 seconds and reconnect. This clears the Automatic Tempature Control computer and it will run the calibration test automatically. Turn the ignition to run and turn the climate control on. The actuator will begin to rotate clockwise. Once the key is in the correct position turn off the ignition and disconnect the battery.

Push the new door onto the connector and slide the connector pin all the way into the installed door.

Install the second door, sliding the connector pin into the far side of the second door. Align and snap in the near connector.

Reinstall the near actuator and test. When you put the ignition to run and turn on the climate control system it will run though the calibration test that broke the OEM equipment to begin with. Watch the doors move, and pay attention to the amount of torque applied to the doors - the plastic ones didn't stand a chance!

Be prepared to remove and tighten the connector / hinge mating. Once you are satisfied the connection is secure, duck tape the doors to cover the holes. Replace the cut piece of plastic and tape, and you're finished. Now...what to do with all that money you saved...hmm....
__________________
Work is the curse of the drinking classes.
Likes: (6)

Last edited by Jimmyb; 31-08-2016 at 11:29 PM.

Sponsored Posts
  #2  
Old 31-08-2016
Jimmyb's Avatar
Jimmyb  Jimmyb is offline
Head Honcho
 
Join Date: Jul 2002
Location: Australia
Posts: 12,014
What Jeep do I drive?: XJ
Likes: 803
Liked 836 Times in 473 Posts
Check out my Ride(s)
Default

Thanks for the great tech there Lexx!!
__________________
No.1 Aussie Jeep Forum AusJeepOffroad Merchandise 10'000 Club midlifemate.com
Wiseguy Pizzeria Thailand
Likes: (1)
  #3  
Old 01-09-2016
Ben-n-Jo's Avatar
Ben-n-Jo  Ben-n-Jo is offline
Senior Newbie
 
Join Date: Apr 2016
Posts: 53
What Jeep do I drive?: WG
Likes: 12
Liked 7 Times in 7 Posts
Check out my Ride(s)
Default

Excellent thanks. Great write up.

Sent from my ZTE T84 using Tapatalk
Post New Thread  Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On


» Advertisements_AS2




Powered by vBadvanced CMPS v3.2.3



All times are GMT +10. The time now is 09:17 AM.




AJOR does not vouch for or warrant the accuracy, completeness or usefulness of any message, and are not responsible for the contents of any message. The messages express the views of the author of the message, not necessarily the views of AJOR or any entity associated with AJOR, nor should any advice be substituted as technical advice replacing that of a mechanic. You agree, through your use of this service, that you will not use AJOR to post any material which is knowingly false and/or defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, religious, political or otherwise violative of any law. You agree not to post any copyrighted material unless the copyright is owned by you or by AJOR. The owner, administrators and moderators of AJOR reserve the right to delete any message or members for any or no reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold harmless AJOR, the administrators, moderators, and their agents with respect to any claim based upon transmission of your message(s). The use of profile signatures to intentionally mislead or misdirect any member on this forum is not acceptable and may result in your account being suspended. Any trip that is organised through the AJOR forum is participated at your own risk. If you or your vehicle is damaged it is your responsibility, not that of the person that posted the thread, message or topic initiating the trip, nor the organisers of AJOR or moderators of any specific forum. This forum and associated website is the property of AJOR.





Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.

AJOR 2002 - 2018 AUSJEEPOFFROAD.COM. All corporate trademarked names and logos are property of their respective owners. Ausjeepoffroad is in no way associated with DaimlerChrysler Corporation or Fiat Jeep.
www.midlifemate.com wayalife.com jkwrangler.com ausjeepforum.com jk-forum.com canadianjeepoffroad.com cryptoprofitcalculator.net
vB Ad Management by =RedTyger=