hehe thanks for the reply
Quote:
Originally Posted by Gordo
Not MUCH beefier than the pitiful D30, eh ?
|
Yeah they're just a
little more solid than a D30
Quote:
Originally Posted by Gordo
While it's all out why not truss the axle tube ? have seen plenty of this during xwc. Just squared section of half box running the length of the tube to the pig in the middle welded on.
|
Already in progress for the rear, and will also happen to the front when it gets back from the diff shop.
Quote:
Originally Posted by Gordo
Are you shaving the pig for more clearance ? You're gonna have plenty more underhang from pigs that big. Pretty sure they can be shaved and plated (diff cover/bash guard too).
|
It's not really something I'd thought about, although I've heard of people doing it. Do you have any links to info where people have done it before and what's involved? I was hoping the 38.5" tyres would help clear the slightly larger centres
![Smile](http://www.ausjeepoffroad.com/forum/images/smiles/icon_smile.gif)
but the more clearance we can get under there the better!
Quote:
Originally Posted by Gordo
I assume as you're moving the side of the pig you'll be rotating to suit your lift to avoid any poss vibes ?
|
We've asked the diff place to rotate the centre up 12-14 degrees to reduce the angle on the drive shaft, whilst still allowing the pinion bearing to stay lubricated.
Quote:
Originally Posted by Gordo
Rear disc convo while they're out ? Wendleness - u must know- are GQ rear discs easy/cheap to come by ? easy bolt up ? this would be the go I reckon.
|
T'is something I'd considered, but I'm not sure how expensive the calipers are. The discs themselves are relatively cheap. I think for the initial build, we'll stick with the drums on the rear, as they've been freshly rebuilt by the guy I bought them off. Might as well let them wear out before replacing them.
Quote:
Originally Posted by Gordo
Are you going down the painful engineering path or will the beastie be a trailer queen afterwards ? Any gotchas u can see coming up ? Wasn't there a max limit to track increase ?
|
Painful engineering path it is. I've got to keep the thing road registered. I can't see any major dramas with the engineering, but I'll have to have a few more conversations with the engineer as we go along, and check things like steering etc.
Quote:
Originally Posted by Gordo
Going hi-steer at the same time ? Prob not too $$ using pootrol bits...
|
Definately! Much cheaper and easier to do it on a GQ diff than when I looked at doing it to a D30.
Quote:
Originally Posted by Gordo
all the obc xwc dudes run GU front axles and GQ rears for greater CV strength (or so I'm told). Not sure if you could graft GU knuckles to your GQ gear at the same time as re-tubing for even extra beef. OL4x4 boys could prob help with this one...
|
This whole project started as a GU diff conversion, we had a set lined up and all, but they're far too wide, and I got the GQ's dirt cheap. In terms of strentgh, I think the GQ's will suit the Jeep okay, but only time will tell. I didn't want to try and get too tricky and start substituting knuckles. It's pretty complex to do what we're doing as it is (ie. wheelbase stretch etc)
Quote:
Originally Posted by Gordo
Why not chuck and extra tab on top of the pigs for pull-down winch attachments ? (ala werock) those things are COOL !
|
It's like you're reading my mind
![Surprised](http://www.ausjeepoffroad.com/forum/images/smiles/icon_surprised.gif)
I planned to put at least a tab on the front for that purpose, and maybe one on the rear for the future.
Quote:
Originally Posted by Gordo
1 more thing... We expect you to attack every obstaclehope you've been practising changing CVs ![Razz](http://www.ausjeepoffroad.com/forum/images/smiles/icon_razz.gif)
|
When have I been known not to attack an obstacle :P If/when I break a CV in the setup, I'll probably put the Haultech or Longfield CVs in there, which are supposed to be
much stronger. I think it's another matter of testing it and seeing how it goes to judge what the strength will be like.