Everything 2.7 CRD - AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand

Go Back   AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand > JEEP GARAGE > ZJ WJ WG Grand Cherokee
Register Forums Trading Your Jeep New Garage Mark All Read

Post New Thread  Reply
 
Thread Tools Search this Thread
  #1  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default Everything 2.7 CRD

NOTE: I finalised this thread back in 2015 so please don't message me about it as I have moved on and don't follow tyhe information...

This thread is the updated version of WG CRD Filters. As before your input is most welcome but
Use the thread "2.7 Drivers" http://www.ausjeepoffroad.com/forum/...d.php?t=124984 as a chat thread for " Everything 2.7".

This thread is a data thread...................................

Whilst all care has been taken to confirm these numbers the onus is on you to double check.
An * means I use them myself.


Specs and ID's:

Engine: 2.7lt 5 cyl 20valve CRD....WG............ Jeep: ENF .................MB: OM647

Transmission: 5 speed auto............... Jeep: DGJ .....W5J400 ...........MB: 722.6 ...... W5A580

This thread will pertain to those parts that are unique to the 2.7, which means basically Engine and Transmission most other bits are common on other Grands, references will try to show Jeep and MB part numbers, always try to cross reference as this model does have some Jeep part numbers of it's own that will not match common parts on other Grands or similar engines in other MB vehicles. The 2.7 engine does have other variations in MB vehicles the OM612 is similar but some bits aren't, many sensors are common on MB engines including the 3lt CRD so good research is crucial.

It is wise to source a build sheet for your vehicle, it will list every item fitted.
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 07-08-2019 at 01:37 PM.
  #2  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default General Service Parts

Whilst all care has been taken to confirm these numbers the onus is on you to double check.
An * means I use them myself.


NOTE: Part numbers for MB or Freightliner/Dodge Sprinters may not fit your Jeep`2.7 CRD, but try Rockauto and look under Dodge 2004, Sprinter 2500 cross reference part with MB or Chrysler part number and you could be lucky.

OIL FILTERS:
Jeep..........................05086301AA
MB............................6111800009
Repco.*.......................ROF103
Mann Filters.*...............HU718/1K
Hengst *.......................E11HD57
Ryco.*.........................R2606P
Cooper/Wesfil..............WC040

FUEL FILTERS:
Jeep..........................05080477AA
MB............................665 092 00 01 or 6110920101
Mann Filters.*...............WK842/19 or 18
Hengst.*......................H217WK
Ryco.*.........................Z670
Cooper/Wesfil..............WCF158 or maybe WCF114 need confirmation.
NOTE: Some filters look the same but drain plug can be in differn't position, check first.

AIR:
Ryco..*................ A1581
Repco.*...............RAF157 (same as ZG)
Cooper/Wesfil......WA976
Mann.................C 28 150

FAN BELT:
Dayco.*.................6PK2605 (number will reference to all brands)
Jeep....................53013 600AA
MB......................0149975692

RADIATOR HOSES:
http://www.mackayrubber.com.au/conte...alogue-search/
Upper radiator hose: CH4078
Lower radiator hose: CH4067


REAR AXLE BEARINGS:

Diff:..Dana 44A...........44/226mm...........Timken Set 31...plus Oil Seal Timken 2146........Aussie bearing shops may show nil listing so you want a Timken Bearing NP182140-904A1 with a lock ring K35961. Show them this pic to prove it. Numbers are confirmed as they are on mine, bought from Rockauto.




I get my filters from MBSpares in canberra http://www.mbspares.com.au/ quote the MB number, they provide Hengst, Bosch and Mann filters, made in germany and they are good, the price is bloody good, you must quote a MB part number though. They stock your general service parts as well as Tranny Oil, MB spec at a fantastic price.
Attached Thumbnails
Click image for larger version

Name:	Timken.JPG
Views:	8364
Size:	16.4 KB
ID:	71041  
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 28-02-2018 at 05:30 AM.
  #3  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default Transmission/Transfer Case

Auto Trans: Jeep W5J400 MB: W5A580 Spec:MB 722.6)
Jeep....Gasket.................5210833
Jeep....Filter....................52108325AA
MB......Filter with gasket.*................1402770095 S1
Mann Kit........................H182
Ryco....................RTK92 ..........note: check it's the right one as RYCO listing was incorrect.
Conductor Plate...........Jeep....52108308AA.............MB. ....140 270 11 61

Video about the 722.6 tranny..................…..


Auto Oil: (Jeep W5J400...MB.. W5A580 MB722.6

MB.*................001 989 21 03 (spec 236.10 )
Shell..............SPIRAX S4 ATF 3403 (haven't found any)
MB upgraded spec to 236.14 following meets that spec by MB.
Fuchs TITAN ATF 4134
Mobil ATF 134
Shell ATF134
Shell SPIRAX S6 ATF 134M
Valvoline SYNPOWER ATF 134
While the ATF134 is specced, not available in Australia.
Check oil company Lube Guides but confirm the MB spec 236.10 or 236.14 some are incorrect with ref for the 2.7. if it has the MB spec it is okay.
Penrite multi vehicle full syn ATF and MV semi-syn ATF meet 236.10
Fusch ATF134 available at Don Kyatts, Darwin,, so might be found elsewhere.
Do not use ATF+4 in this box.

Transfer Case Oil:

* MobilFluid 424............about 2lts per change. (Mopar fluid is 10x the price and believe 424 is the same stuff)
http://www.eclubes.com.au/products/v...mobilfluid-424


Drive Shafts:
The front drive shaft has replacable bearings.
Front shaft rear bearing: hardy-spicer CV-861 (same as on a BA XR8
Front shaft front bearing: TBA

Whilst all care has been taken to confirm these numbers the onus is on you to double check.
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 13-05-2014 at 08:45 PM. Reason: more numbers
  #4  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default Idler Pulleys and Tensioners.

Idler Pulley and Tensioner

Jeep.(3)..............05080422AA (tensioner).....Nuline...EP253 (pulley only).....Repco....RPU753 (pulley only)
Jeep..(7).............05080246AA.....Nuline...EP25 0.....MB...6112583180.................Repco....RPU750
Jeep..(12 & 18...05080243AA ....Nuline...EP253..... MB...6112000570...............Repco....RPU753
Numbers in brackets refer to diagram in post below.
Alternator Pulley........Nuline...OAP007...IAT.....IAT391014
Link to post on subject; http://www.ausjeepoffroad.com/forum/...18#post1258018
and here http://www.ausjeepoffroad.com/forum/...=118342&page=2

NOTE: Available from Bursons, Repco, Supercheap etc.





This section is from Festers post in the above links:


OK lets see if we can clarify a bit more, here is the layout as per Nulines catalogue:

So the 253 is the smooth idler bearing/pulley and is available.
The 250 is the ribbed tensioner pulley but is apparently not available. It is the pulley only not the whole tensioner assembly.
The OAP007 is the alternator overrun bearing/pulley and is available.
These are all the Nuline part numbers.
Other part numbers for the alternator pulley are:
Klarius QH available through Rock Auto 1010101
INA through IAT is IAT391014. I found it throough that ebay link of Pipers but a search for IAT for me did not pick them up yet.
This is the page from the Nuline catalogue that shows the 250 pulley and the ones close to it if you want to source them.

The 262 and 046 look worth investigating and Piper has used the 026.
It is also possible that if the bearings can be pressed out of the pulleys then that will be a cheap fix as most of those bearings should be cheap and available from your local bearing shop. Bodgie has replaced the bearing only in the tensioner pulley under bearing number 6203ATN-RSVC3.
The bearing inside the heater clutch is also a standard style bearing similar to most A/C compressors and a number for that is 35BD5222DUM18A (OD=52mm, ID= 35mm, Depth=22mm),
I would suggest if you have original steel or Nuline steel pulleys then it would be worth seeing if you can replace the bearings only assuming the pulley is in sound condition. If you have plastic pulleys already and they are in need of fixing then it would be better to replace the whole pulley as a unit.
I also think I noticed Rock Auto had the whole tensioner assembly under their Sprinter listing if you need the whole thing.

If I'm wrong please speak up and clarify and hopefully Drover can put this info into the sticky topic where it will be easier to follow. If someone else has used a replacement for the 250 please clarify likewise if you have replaced the bearings in a 253 and have a number please clarify.
__________________
Whilst all care has been taken to confirm these numbers
the onus is on you to double check.
Uploaded with ImageShack.us
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 04-05-2014 at 02:01 PM.
  #5  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default Engine Parts

Whilst all care has been taken to confirm these numbers the onus is on you to double check.

FUEL LINES:

Filter to Pump
Jeep..................5080482AB
MB....................A6650700532

Low to High Pressure Pump:
Jeep.....................5080483AA
MB.......................6650700132

Pump to Fuel Rail
Jeep..................5080295AA (solid tube to fuel rail)
MB....................researching
HP Pump return to rail::
MB....................6120703232 (plastic line) or 6120703332
Jeep.................. 5140799AA
Return Valve on Filter:

Jeep................5080460AA
MB..................A6110780249
Bracket – double tube clip for underneath HP pump:
MB A6110781241

Fuel Line "O" Rings:
MB.....................6019970645................. .($4.75 each )
Link to post on subject: http://www.ausjeepoffroad.com/forum/...ight=fuel+line

Fuel Pump:
High Pressure......MB A6120700001 Jeep.......5080278AA Bosch.....0445010019
O-rings for high pressure pump;
Bosch o-rings 6 x F01M 100389.
Support rings 6 x F01M 100643,
o-ring 3 x F01M 0P0 743
sealing ring 3 x F00R 0P0 577
sealing ring 3 x F00R 0P0 480
Link for HIgh Pressure Pump Replacement:
http://www.jeepforum.com/forum/f310/...hotos-1410217/

Service Kit for Bosch Pump 0445010019....................... F 01M 101 455..........MB...A0000780780

Low Pressure......MB.. ?? Jeep......5080255AA Bosch..... ??

DRV Valve: (fuel pressure)...MB.....6110780149.....Bosch......02810 02698....confirmation on Bosch number needed.

INJECTORS:

BOSCH....................0445110097 (OME)
Jeep.......................RX137254AB (5080300AA old number)
MB.........................A 611 070 16 87

Washer......MB............A6110170060
Bolt..........MB............A 004 990 28 12 ............Jeep........5073 719AB
Grease......MB............MA0019894251/10

GLOW PLUGS:

Jeep:........5080046AA
Bosch:......250202045..(OME)
MB:...........0011594201 ?????
NGK:.........Y-745U
Available from Repco etc.

Crankshaft Position Sensor
MB.........003 153 28 28

Jeep....... 5080 352AA
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 09-09-2015 at 06:18 AM.
  #6  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default Online Links parts and info.

Dana/Spicer Diff Parts list: http://www2.dana.com/pdf/X510-6.pdf (Note you will need the BoM number for your diff which is on one of the tags then you can ID specifically the parts in your diff) go to http://www2.dana.com/expertforms/demenu.aspx for more info )

Timken Online Parts Reference: http://www.showmetheparts.com/timken/

MB oil/fluid specs:
http://bevo.mercedes-benz.com/index.php?language_id=1 (eng OM647, auto spec: 722.6 )

Oil/Fluid Specs: https://docs.google.com/file/d/1YxT7...nLLHwnsEA/edit ( does need updating).

Workshop Manual: http://colorado4wheel.com/manuals/Je..._WJ:WG_Diesel/ ( worked 11/14)

Fault Code Listings: these are general WJ/G listings, not all pertain to the 2.7 CRD. Refer to manual for concise list.
http://www.wjjeeps.com/faultcodes.htm

Jeep Parts List: http://autoricambi-euroamerica.com/

Paint Codes: http://www.automotivetouchup.com/paint-codes/jeep.htm

Online Parts:

http://www.atlasparts.com.au/radiato...utmk=264084364 radiator

www.dencodiesel.com/index.php

www.rockauto.com

www.factorymopar.com

http://www.sprinterparts.net/mercede...ter-parts.html (tap in your Jeep part number)

http://uk.mbspecialist.com/

https://www.mann-hummel.com/mf_prodk...=1&ktlg_lang=1


https://www.germanautosupply.com/sto...edes-benz.html

http://www.westernfilters.net.au for filters, pulleys etc.

www.mbspares.com.au ( australian supplier of Benz parts)

TC parts: http://cobratransmission.com/index.p...x&cPath=3_2100


TC OIL: http://www.eclubes.com.au/products/v...mobilfluid-424

Transmission : Best FAQ on the 722.6 tranny.

http://www.benzworld.org/forums/w210...ssion-faq.html

Seat Motor Parts:
http://www.2men1garage.net/Jeep-Gran...004-Parts.html

Lights/Globes/LED's:

http://www.eziautoparts.com.au/lighting.htmlhttp://www.brightlightautoparts.com/index.html

http://www.narva.com.au/products/globeChart

Light Globes:
festers comments: Anyway I can categorically confirm that the front indicator bulb in a CRD WG is not the 3157 as per wjjeeps and the FSm but it is in fact an Osram 7507 which as far as my research can tell is a BAU15s. Single contact offset pins bayonet.

Rear lights; they are all the same globe , if the brake or turn sig blows just swap it with the fog globe whch is the very bottom one. see pic. While the pic shows as Wagner 3157 I pretty sure they are a Narva 47557.

Cross reference Jeep number to make sure you get the correct part, not all 2.7 engine parts will match. The 2.7 engine came out as a OM612 as well as a OM647 the engine in your Jeep is an OM647.
Attached Thumbnails
Click image for larger version

Name:	RearGlobe.jpg
Views:	1060
Size:	128.4 KB
ID:	64910  
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 24-07-2015 at 09:25 PM.
  #7  
Old 30-04-2013
drover's Avatar
drover  drover is offline
MonsterMoose
 
Join Date: Apr 2005
Location: QLD
Age: 69
Posts: 8,707
What Jeep do I drive?: WK2
Likes: 4,309
Liked 3,854 Times in 2,282 Posts
Default How To's 2.7 CRD's

EGR Defeat for 2.7 CRD:
http://www.ausjeepoffroad.com/forum/...ighlight=shuntlink to explanation of why and what EGR is; http://www.chiptuning.com.au/egr_blanking_info/

Oil in Coolant Tank: (leaking engine oil cooler)

http://www.ausjeepoffroad.com/forum/...ght=oil+cooler
http://www.ausjeepoffroad.com/forum/...hlight=coolant

Tranny Conductor Plate
:
http://www.benzworld.org/forums/w210...tor-plate.html

Hydraulic Solenoid repair solution link :
http://www.ausjeepoffroad.com/forum/...d.php?t=117612

HIgh Pressure Pump Replacement:
http://www.jeepforum.com/forum/f310/...hotos-1410217/

rebuild: http://www.ausjeepoffroad.com/forum/...d.php?t=130175

Idler Pulley and Tensioner
http://www.ausjeepoffroad.com/forum/...18#post1258018
and here http://www.ausjeepoffroad.com/forum/...=118342&page=2
REPLACEMENT: http://www.ausjeepoffroad.com/forum/...d.php?t=124827


Cam & Crank sensor replacement:
http://www.ausjeepoffroad.com/forum/...d.php?t=124823

Alternator Overhaul:
http://www.ausjeepoffroad.com/forum/...d.php?t=124830

Seat Motor Replacement:
http://www.ausjeepoffroad.com/forum/...seat+adjusters

DIY Tranny Service:
http://www.ausjeepoffroad.com/forum/...d.php?t=106682

Clearing 2.7 CRD Adaptive Gearbox Learning:
http://www.ausjeepoffroad.com/forum/...d.php?t=132093

Injector Replacement: link to some informative sites includes Black death.

First off you will need to cut a couple of holes to get at the rear ones, here's what Ozjeepster has said on the subject;
Quote: Pull the plenum shroud off remove the wiper motor and remove the wiper harness out of the way there will be a small hole for a xmas tree plug dead center over injector 5 use that as a guide for 64mm holesaw i put a thin sheet of MDF over the injectors to stop the the saw from punching into them , take care when removing the return line as the plastic can be brittle apply even pressure to each side and wiggle out and once you have it out make sure you replace the fork bolt that locks the injector in place and the new one is torqued too 7NM + 90 degrees if you exceed this you run the risk of punching through into a coolant chamber and the head is stuffed . "Unquote"


http://www.4x4community.co.za/forum/...t=27700&page=2

http://sprinter-source.com/forum/sho...t=27700&page=2

Timesert link: for stripped injector bolt........http://www.timesert.com/html/1610E2-note.html
for Australian timeserts, need in a hurry http://www.crosstools.com.au/
__________________
2015 WK2 CRD Laredo( ZG, WG 2.7 )

Your Never Too Old To Learn Something Stupid.

Last edited by drover; 21-04-2015 at 01:18 PM.
Post New Thread  Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On





All times are GMT +10. The time now is 02:33 PM.


Advertisements




AJOR does not vouch for or warrant the accuracy, completeness or usefulness of any message, and are not responsible for the contents of any message. The messages express the views of the author of the message, not necessarily the views of AJOR or any entity associated with AJOR, nor should any advice be substituted as technical advice replacing that of a mechanic. You agree, through your use of this service, that you will not use AJOR to post any material which is knowingly false and/or defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, religious, political or otherwise violative of any law. You agree not to post any copyrighted material unless the copyright is owned by you or by AJOR. The owner, administrators and moderators of AJOR reserve the right to delete any message or members for any or no reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold harmless AJOR, the administrators, moderators, and their agents with respect to any claim based upon transmission of your message(s). The use of profile signatures to intentionally mislead or misdirect any member on this forum is not acceptable and may result in your account being suspended. Any trip that is organised through the AJOR forum is participated at your own risk. If you or your vehicle is damaged it is your responsibility, not that of the person that posted the thread, message or topic initiating the trip, nor the organisers of AJOR or moderators of any specific forum. This forum and associated website is the property of AJOR. No user data is harvested and no information supplied in your registration will be sold for profit.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

AJOR © 2002 - 2024 AUSJEEPOFFROAD.COM. All corporate trademarked names and logos are property of their respective owners. Ausjeepoffroad is in no way associated with DaimlerChrysler Corporation or Fiat Jeep.
www.ausjeep.com www.ausjeep.com.au www.midlifemate.com ausjeepforum.com www.r9kustoms.com
vB Ad Management by =RedTyger=