WG CRD mega part listing

[Adrian D]

Most of the part numbers are Mercedes Benz, it's easier to find parts in Europe by a Mercedes Benz part number and if part sellers annoy you, you can just go to the dealership.

Engine:
Fuel line O-rings: A 601 997 06 45
Oil separator O-rings: A 611 997 05 45; A 611 997 06 45
Oil separator: A 611 016 03 34
High-pressure pump seal kit: F 01M 101 455 (Bosch); A 000 078 07 80
Low-pressure pump: A 611 090 03 50
Pressure regulator: 0 281 002 241 (Bosch); A 611 078 01 49
Pressure regulator seal kitt: A 014 997 70 45
Oil filter: Mann HU718/1K
Fuel filter (without sensor and drain): Mann WK842/13
Fuel filter (with sensor and drain ports): Mann WK842/18
Air filter: Mann C28150
Fuel pressure sensor: 0 281 002 239 (Bosch); A 004 153 75 28
Fuel line from filter to LP pump: A 665 070 05 32 (confirmed ok)
Fuel line from LP pump to HP pump: A 612 070 33 32 (confirmed ok)
Fuel line from pressure regulator to HP pump: A 612 070 33 32 (confirmed ok)
Injector grease, ceramic: A 001 989 42 51/10; Liqui Moly 3381, Liqui Moly 3420, Febi 26712
Injector bolt: A 000 990 29 07
Injector seal, 1.56mm thick (normal): A 611 017 00 60 L/L; ELRING 924.867
Injector seal, 1.76mm thick: ELRING 199.360
Injector seal, 1.96mm thick: ELRING 199.340
Cam cover seal set: ELRING 330.370; Victor Reinz 15-36224-01
Cam cover: A 612 016 08 05 (research shows it fits)
Oil pan gasket: A 647 014 00 22
Cam sensor: A 005 153 13 28
Crank sensor: 0 261 210 170 (Bosch); A 003 153 28 28
Oil cooler gasket: A 611 184 02 80
Oil cooler: Hella 8MO 376 726-321
Oil pump inlet o-ring: A 027 997 38 48; Elring 003.360; 22x4 mm
Oil pump to block o-ring: A 019 997 80 48; Elring 294.430; 16x3 mm
Fuel filter return valve: A 611 078 02 49
Harmonic balancer: A 612 030 02 03
MAP: A 004 153 31 28
Injector: A 611 070 16 87
Accesory belt: 6PK2604
Exhaust manifold nuts: A 120 142 00 72
Exhaust manifold studs: A 111 990 04 05; Febi 46388
Turbo to resonator O-ring: A 01 299 722 45
Intercooler hose O-ring (at resonator connection): A 02 699 782 48
Turbo resonator: A 611 098 18 07
High-pressure pump hose outer seal (white donut): A 006 990 60 40
Vacuum pump O-ring: A 611 997 07 45
Intake manifold gasket: A 612 141 01 80
Turbo seal (or install) kit: Victor Reinz 04-10044-01


Starter motor:
0001223005 / A0051512901
M2T88572 / M2T88571
S5155 / S5098

Gearbox:
Connector plug: A 203 540 02 53
Torque converter: A 210 250 0602
Torque converter bolt cover: A 611 014 00 33 (makes strange noises if it's missing, like a heavy engine knock from below)
Conductor plate: Febi 32342 (OEM, with the Benz part number sanded off)

Body / General:
Turn signal relay, works with LED's too: Novita LM519
Transfer case lever bushing: 53004810
Climate control bulbs: 7382 (Farnell); 2162 (JKL)
Heated seat switch bulb: 05012591AA; JKL DNW1-DW33/GRA/39-04-5T
Gearbox mount: A 203 240 19 17; Febi 19679
Viscous heater bearing: 35mm ID X 52mm OD x 22mm
Viscous heater coil: CARGO 250037
Downpipe gasket: FA1 141-965
Downpipe clamp: FA1 144-974
Coolant sensor: 52079881AA
Ribbed idler pulley, 70x26x17: Febi 30289
Smooth idler pulley, 70x26x17: Febi 31975; Gates T38099
Steering box seal set: 5014665AA
Cabin air filter kit: 82208300

Most are checked by me since I had so much to change on my car

I've got no idea how to format it to make it look nice.

When I have new part numbers I will update it. Let's keep this clean, please ask any questions in a new topic.

[JeanLuke]

The parts in bold font are all ones I have purchased and are fitted to my WG - so confirmed to work:

Turbo vacuum control valve (and also EGR control): MB A0005450527

Power steering hose from pump to hydraulic fan: The fitting at the pump often leaks. The V8 hose can be fitted, but will require increasing the angle of the bend out of the pump. Can easily be done in a bench vice. It will lightly touch the intercooler-to-manifold intake hose.
Part numbers:
EDELMANN: 92189
GATES: 36557
ACDELCO 36365571
SUNSONG 3402495
MOPAR: 05019708AD, 05019708AE

Intake pipe from intercooler to manifold: The Dodge Sprinter one fits and if you have installed the V8 power steering hose (above) it clears it.
Part Number: 9015284382

Wiring harness repair kit for transfer case position sensor (sold as ignition coil connector): WVE/AIRTEX/WELLS 1P1792

Engine air filter (sold to suit 2006 Nissan Pathfinder 4.0L V6): WIX 46213

Engine mount bushes (re-use the aluminium casting - press in new bushes): Eagle BHP 1116R

Wiring repair kit for water-in-fuel sensor (sold as brake differential valve connector): Standard Motor Products S1238

[RollinCoal]

Cracking Information

Does Gearbox mount: A 203 240 19 17 need the protruding nib taking down level?

[bezzat]

Originally Posted by RollinCoal

Cracking Information

Does Gearbox mount: A 203 240 19 17 need the protruding nib taking down level?

buy from here
https://www.rockauto.com/en/parts/we...tor+mount,5552

my post
http://www.ausjeepoffroad.com/forum/...47#post1644047

[RollinCoal]

Originally Posted by bezzat

buy from here
https://www.rockauto.com/en/parts/we...tor+mount,5552

my post
http://www.ausjeepoffroad.com/forum/...47#post1644047

Good Man.. Thank you. I hadn't seen that post.

They're cheaper than Rockys for me from within Europe.

Once bolted all back up I think with lobbing the tab off there wound't be much chance of it rotating... But I do like the idea of drilling the hole. More OE

[dbech]

Has anyone got part numbers for the rear axel seals/bearings for the limited? I believe it comes with a Dana 35

[JeanLuke]

Originally Posted by dbech

Has anyone got part numbers for the rear axel seals/bearings for the limited? I believe it comes with a Dana 35

In Australia, I believe it was only the Dana 44HD (aka 44A). For the 44A you want the Timken Set 31. I struggle to find them in Australia. For some strange reason Timken don't bring them here. You can get them from Amazon.