REVIEW: Runva 11XP Winch - Page 5 - AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand

Go Back   AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand > PORTAL > REVIEWS & NEW PRODUCTS
Register Forums Trading Your Jeep New Garage Mark All Read

Post New Thread  Reply
 
Thread Tools Search this Thread
  #29  
Old 14-01-2015
SeaComms's Avatar
SeaComms  SeaComms is offline
MonsterMoose
 
Join Date: Jun 2010
Location: Noosa QLD.
Age: 58
Posts: 7,940
What Jeep do I drive?: WK2
Likes: 1,432
Liked 809 Times in 466 Posts
Check out my Ride(s)
Default

Ditto on the power cable lengths! Simple enough to install just a thought process as to where to mount stuff. On mine (not a Runva I should add) the control box was designed to mount on top of the winch as many do. In the ARB bar on the JK the winch left a gap on the passenger side large enough to comfortably fit the control box so it dropped down to the same level as the winch reducing air blockage in front of the grill and making it less obvious.

However as the electrical connections to the winch are on the other end (drivers side when installed) the cables from control box to winch were a few inches short. First obvious option is to replace with longer cables but unless you have the ability to crimp connectors properly onto cable that thick you are asking for trouble. So what I did was to go to Supercheap and grab 2 x 30cm battery cables premade with connectors. Simply used a good quality bolt and nut to join them together then wrap up the join and seal (I happened to have a roll of self amalgamating rubber tape from aircraft wiring looms which sealed it up nicely).

Sent from my SM-G900I using Tapatalk
__________________
Cheers, Dave :)

2010 JK, then a 2015 KL Trailhawk, now a 2017 GC Trailhawk!

Over 5000 Club
  #30  
Old 14-01-2015
Madrax573  Madrax573 is offline
CrawlerStar
 
Join Date: Apr 2011
Location: Soon to be Coffs!
Posts: 340
What Jeep do I drive?: XJ
Likes: 192
Liked 75 Times in 44 Posts
Check out my Ride(s)
Default

I just drilled 'offset' holes on the roller fairlead to fit my ARB bar, fits like a glove now.

If I was going to swap out with rope then I would just remove the rollers and stick on an offset fairlead for the rope. You can then use longer mounting bolts and the bar is stock then without any modification.
__________________
98 Sport
2" lift
30" Bighorns
9000lb Winch
Post New Thread  Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On





All times are GMT +10. The time now is 03:13 PM.


Advertisements




AJOR does not vouch for or warrant the accuracy, completeness or usefulness of any message, and are not responsible for the contents of any message. The messages express the views of the author of the message, not necessarily the views of AJOR or any entity associated with AJOR, nor should any advice be substituted as technical advice replacing that of a mechanic. You agree, through your use of this service, that you will not use AJOR to post any material which is knowingly false and/or defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, religious, political or otherwise violative of any law. You agree not to post any copyrighted material unless the copyright is owned by you or by AJOR. The owner, administrators and moderators of AJOR reserve the right to delete any message or members for any or no reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold harmless AJOR, the administrators, moderators, and their agents with respect to any claim based upon transmission of your message(s). The use of profile signatures to intentionally mislead or misdirect any member on this forum is not acceptable and may result in your account being suspended. Any trip that is organised through the AJOR forum is participated at your own risk. If you or your vehicle is damaged it is your responsibility, not that of the person that posted the thread, message or topic initiating the trip, nor the organisers of AJOR or moderators of any specific forum. This forum and associated website is the property of AJOR. No user data is harvested and no information supplied in your registration will be sold for profit.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

AJOR © 2002 - 2024 AUSJEEPOFFROAD.COM. All corporate trademarked names and logos are property of their respective owners. Ausjeepoffroad is in no way associated with DaimlerChrysler Corporation or Fiat Jeep.
www.ausjeep.com www.ausjeep.com.au www.midlifemate.com ausjeepforum.com www.r9kustoms.com
vB Ad Management by =RedTyger=