WH Guard flares

[JamesLaugesen]

I'm interested, but probably only for something subtle like the SRT8 ones.
Happy to be proven wrong, but I think it'd be real hard to design anything bigger (like the WG bushwacker ones.) which looks good on the WH - Due to the lines of the flared arches.

[Clarky]

Originally Posted by JamesLaugesen

Found the part numbers;

• 1FX44RXFAA - Wheel Opening Flare. Right. Front Fender. Trim: -O0, PO0, . ST. Required: 001
  $125
  http://www.factorychryslerparts.com/...FX44RXFAA.html
  
• 1FX45RXFAA - Wheel Opening Flare. Left. Front Fender. Trim: -O0, PO0, . ST. Required: 001
  $122
  http://www.factorychryslerparts.com/...FX45RXFAA.html
  
• 1FX46RXFAA - Wheel Opening Flare. Right. Front Fascia. Trim: -O0, PO0, . ST. Required: 001
  $82.10
  http://www.factorychryslerparts.com/...FX46RXFAA.html
  
• 1FX47RXFAA - Wheel Opening Flare. Left. Front Fascia. Trim: -O0, PO0, . ST. Required: 001
  $82.10
  http://www.factorychryslerparts.com/...FX47RXFAA.html
  
• 1FX48RXFAA - Wheel Opening Flare. Right. Quarter Panel. Trim: -O0, PO0, . ST. Required: 001
  $85.50
  http://www.factorychryslerparts.com/...FX48RXFAA.html
  
• 1FX49RXFAA - Wheel Opening Flare. Left. Quarter Panel. Trim: -O0, PO0, . ST. Required: 001
  $85.50
  http://www.factorychryslerparts.com/...FX49RXFAA.html
  
• 1FX50RXFAA - Wheel Opening Flare. Right. Rear Door. Trim: -O0, PO0, . ST. Required: 001
  $87.50
  http://www.factorychryslerparts.com/...FX50RXFAA.html
  
• 1FX51RXFAA - Wheel Opening Flare. Left. Rear Door. Trim: -O0, PO0, . ST. Required: 001
  $87.50
  http://www.factorychryslerparts.com/...FX51RXFAA.html
  
• 1FX52RXFAA - Wheel Opening Flare. Right. Rear Fascia. Trim: -O0, PO0, . ST. Required: 001
  $82.10
  http://www.factorychryslerparts.com/...FX52RXFAA.html
  
• 1FX53RXFAA - Wheel Opening Flare. Left. Rear Fascia. Trim: -O0, PO0, . ST. Required: 001
  $82.10
  http://www.factorychryslerparts.com/...FX53RXFAA.html

From this forum. Some good detailed photos there.

... $1,000 anyone? Hmm.

Current price on these less the front bumper bits as I have B/Bar including postage $717.46 Aus Dollars
If the link works here is the shopping cart
http://www.factorychryslerparts.com/cart.aspx

Not to bad a price really.

[fester]

Originally Posted by JamesLaugesen

Happy to be proven wrong, but I think it'd be real hard to design anything bigger (like the WG bushwacker ones.) which looks good on the WH - Due to the lines of the flared arches.

No different to the WG really and quite easily dealt with by a good fibreglasser.

[Clarky]

Cheap knockoff SRT8 flares $130


http://www.deluxeautomall.com/jeep-g...-6-p-4199.html

[JamesLaugesen]

Originally Posted by Clarky

Cheap knockoff SRT8 flares $130


http://www.deluxeautomall.com/jeep-g...-6-p-4199.html

I've been looking at them, hard to tell how much they extend out.
Pretty cheap though so I might grab some for an experiment. Could even be good for moulding thicker ones around.

[jorgo]

James did you end up buying a set of these? curious how wide they are.

[mercury68]

You could have a look at TJM Flex Flares which are either 65mm or 35mm wide.