Jeep hubs on a Jayco - AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand

Go Back   AUSJEEPOFFROAD.COM Jeep News Australia and New Zealand > ASSOCIATED INTERESTS > Camper Trailers and Caravans
Register Forums Trading Your Jeep New Garage Mark All Read

Post New Thread  Reply
 
Thread Tools Search this Thread
  #1  
Old 24-12-2017
lujabe  lujabe is offline
Newbie
 
Join Date: Jan 2015
Posts: 342
Likes: 39
Liked 151 Times in 92 Posts
Default Jeep hubs on a Jayco

Hi all,

We’ve recently bough a Jayco camper, and looking to optimise it a little more for outback/remote touring (outback roads, not ‘off-road’ as such).

Thinking of swapping the 6-stud hubs on the camper to match the 5-stud on my KL to enable wheels and spares to be interchanged.

Has anybody done this or something similar? I’m trying to get an idea of complexity and how much I could expect to pay to have it done?

Any thoughts/advice appreciated!
  #2  
Old 24-12-2017
Notso  Notso is offline
Newbie
 
Join Date: Apr 2016
Posts: 31
What Jeep do I drive?: WK
Likes: 0
Liked 4 Times in 3 Posts
Check out my Ride(s)
Default

Might try this lot.

https://www.ebay.com.au/itm/Ford-F10...sAAOSwzrxUrjE0
  #3  
Old 24-12-2017
DAVE M's Avatar
DAVE M  DAVE M is offline
Established Member
 
Join Date: Jan 2004
Location: PORT LINCOLN. SA
Posts: 214
What Jeep do I drive?: TJ
Likes: 4
Liked 16 Times in 10 Posts
Default

You need to find a good trailer chassis/parts supplier. First you need to know what bearings are in your existing axle/hub assy. You also need to check whether you KL hubs will fit over the nose of the hub. Also check back spacing of you existing trailer wheels and any new wheel you intend to use. It is relatively easy if you get some good trade assistance.

The hub in the referred add is a bit over the top. If you are only using Holden or Ford bearings the hub should be about $25. Plus bearings.
Recommend brand name bearings NTN, SKF, Timken, NSK, Koro not Chinese. Again, if it is only Holden or Ford, bearings should be $25 to $35 per wheel.

Holden bearings are rated at one tonne per axle, Ford(slimline) at one and a quarter tonne per Axle.

Most new vans and campers have much higher rated axles, 1.5, 1.6, 2 and 3 tonne capacity. This is where it gets tricky and dearer.

Any hub/drum for axles with brakes will be dearer than those prices suggested above.

Don’t be pu off. It is a good idea. Find a good trailer axle supplier.

By the way, where are you located?
  #4  
Old 25-12-2017
layback40's Avatar
layback40  layback40 is offline
Grumpy Old XJ Dsl Owner
 
Join Date: Jan 2011
Location: Northern Victoria
Posts: 13,781
What Jeep do I drive?: XJ
Likes: 4,579
Liked 6,550 Times in 4,342 Posts
Default

I put ford hubs on my poptop camper. Simple as. Purchased them from Huntsman in Melbourne. They have adds for things on ebay. If you go to their warehouse they give good discount for cash.
__________________
98&01XJVMs,06&07KJCRD's,No longer question authority,I annoy it.More effect,less effort.10000Club
  #5  
Old 27-12-2017
xjrob's Avatar
xjrob  xjrob is offline
Full Flexer
 
Join Date: Nov 2006
Location: Brisbane
Age: 67
Posts: 736
Likes: 0
Liked 28 Times in 13 Posts
Default

Thats all fine, I also put 5 x 4.5 hubs on my camper trailer.

However, as DaveM said you need to know what bearings are being used, most probably Jayco will be using SL (Slimline often called Ford) they are slightly larger than the Holden bearing many smaller box trailers use.

However the other point DaveM made was back space, i have aftermarket Alloys on my XJ so it was not an issue, if I try to use the standard steel wheels with 5.25" back space the clearance is very limited, and i needed to grind about ˝ mm off the centre hubs to fit the rims over.

The KL i think uses a front wheel drive type offset which may mean that other than the wheel centre being too small not sure how much will need to be trimmed, they are likely to rub on the inner guard of the camper.

All things that need to be checked. many people have just purchased and fitted very easy job, however, some are just plain lucky and don't have issues, measure everything first as back space and the wheel centre hole can be issues, if not to much just as i did start the angle grinder and slowly rotate the hub until the wheel fits over. But measure back space first because after all that f????ing around i did not have acceptable clearance using standard wheels, the aftermarket alloys had 4" back space and worked perfectly.
__________________
XJ Sport - finally some mods - still long wish list
  #6  
Old 31-12-2017
lujabe  lujabe is offline
Newbie
 
Join Date: Jan 2015
Posts: 342
Likes: 39
Liked 151 Times in 92 Posts
Default

Thanks for your thoughts guys. Having given it a bit more thought I figure I’ll probably end up going for a second spare rim & tyre in each size for both the Jeep and the Camper. For the likely cost of swapping hubs plus an extra rim and tyre (as a 3rd spare to share between Jeep and Camper) - I could probably just buy 2 new spare rims/tyres. That gives me a bit better insurance against punctures and keeps it simple.

Thanks again for your input - much appreciated.
  #7  
Old 01-01-2018
DAVE M's Avatar
DAVE M  DAVE M is offline
Established Member
 
Join Date: Jan 2004
Location: PORT LINCOLN. SA
Posts: 214
What Jeep do I drive?: TJ
Likes: 4
Liked 16 Times in 10 Posts
Default

Just before you go down that track, take a photo of you trailer hub, preferably without the wheel for us. As I said earlier this maybe easier than I implied.
Post New Thread  Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off





All times are GMT +10. The time now is 04:29 PM.


Advertisements




AJOR does not vouch for or warrant the accuracy, completeness or usefulness of any message, and are not responsible for the contents of any message. The messages express the views of the author of the message, not necessarily the views of AJOR or any entity associated with AJOR, nor should any advice be substituted as technical advice replacing that of a mechanic. You agree, through your use of this service, that you will not use AJOR to post any material which is knowingly false and/or defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, religious, political or otherwise violative of any law. You agree not to post any copyrighted material unless the copyright is owned by you or by AJOR. The owner, administrators and moderators of AJOR reserve the right to delete any message or members for any or no reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold harmless AJOR, the administrators, moderators, and their agents with respect to any claim based upon transmission of your message(s). The use of profile signatures to intentionally mislead or misdirect any member on this forum is not acceptable and may result in your account being suspended. Any trip that is organised through the AJOR forum is participated at your own risk. If you or your vehicle is damaged it is your responsibility, not that of the person that posted the thread, message or topic initiating the trip, nor the organisers of AJOR or moderators of any specific forum. This forum and associated website is the property of AJOR. No user data is harvested and no information supplied in your registration will be sold for profit.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.

AJOR © 2002 - 2024 AUSJEEPOFFROAD.COM. All corporate trademarked names and logos are property of their respective owners. Ausjeepoffroad is in no way associated with DaimlerChrysler Corporation or Fiat Jeep.
www.ausjeep.com www.ausjeep.com.au www.midlifemate.com ausjeepforum.com www.r9kustoms.com
vB Ad Management by =RedTyger=